50mm
Slip mat
Place the slip mat on the platter. Then place a record on
top of the slip mat. By using a slip mat, it becomes
possible to stop a record board by hand during rotation of
a platter or to make it reverse. Moreover, if an optional
slip-sheet is set and used, it will take effect more.
Cartridge Installation
(1)Make sure that you follow the instructions included with
your cartridge.
(2)Connect the lead wires to the respective terminals.
Industry standard cartridges come with color-coded
wires. Make sure that you match these colors correctly.
Red (R+) Right Channel+ Green (R-) Right Channel -
White (L-) Left Channel+ Blue (L-) Left Channel -
(3)The overhang of your cartridge needs to be adjusted to
best suit the A.S.T.S tone arm. For best tracking and
stylus pressure a distance of 50mm (as shown) should
be set.
(4)Insert the head shell into the front part of the tone arm.
Turn the looking ring in the direction shown below until
the head shell is firmly fixed in place.
NOTE
If using a lightweight cartridge, we suggest the use of
the shell weight enclosed.
NOTE
To avoid premature damage to the stylus take care to
avoid touching it during any adjustment(s).
-10-
Top:Record disc side(Printed side)
Bottom:Slip surface side
NUT
HEADSHELL
(OPTION)
SHELL WEIGHT
(OPTION)
CARTRIDGE
STYLUS
SCREW
LEAD WIRE
-7-
MADE IN CHINA
LINE 2 LINE 1
L
R
MASTER
OUT
SERIAL NO.
100V 50/60Hz 15W
MODEL NO. QFO
18 17 18 19
SIDE
BOTTOM
REAR PANEL
worn out. Please see the "EXCHANGE THE FADER
UNIT" section of this manual.
uMASTER LEVELVOLUME
Adjusts the signal level outputs from MASTER OUT.
iMASTER MUTE SWITCH
This is the switch which mutes the output sound signal
from MASTER OUT jack of the rear panel. If you turn
the switch on, the output will be muted.
oMONITOR SELECT SWITCH
This switch is used to select the way of monitoring from
following.
PGM1･････ It allows you to hear input signal of PGM1.
MASTER ･･ It allows you to hear the signal of MASTER
OUT.
PGM2･････ It allows you to hear input signal of PGM2.
!0POWER SWITCH
Use to turn power on.
!1C.F. CURVE SWITCH
Select the cross fader curve. When this switch is slide to
right side it gives a steep cross fader good for
scratching and cutting. When sliding to the left side it
gives a gentle cross fader good for long running mixes.
!2PHONES LEVEL VOLUME
Adjusts the headphone monitor level.
!3PHONES2 JACK -MINI JACK(φ3.5)
Connect the headphones with a 1/8" mini headphone plug.
(the impedance of 8ohm to 600ohm)
!4PHONES1 JACK -PHONE JACK(φ6.3)
Connect the headphones with a standard 1/4" stereo
plug. (the impedance of 8ohm to 600ohm)
!5I.F. REVERSE SWITCH
Reverses the action of the input fader by marking the
zero point top instead of bottom.
!6C.F. REVERSE SWITCH
Reverses the action of the cross fader by switching
PGM1 and 2.
!7MASTER OUT JACK
Connect to the line/AUX input of power amplifier/mixer.
!8LINE INPUT JACK
Connect the equipment with line level output (-10dB or
0dB), such as CD players, tape decks, DATs, MDs, etc.
The signal from line level equipment is fed to the PGM
channels when Line input is selected.
!9AC POWER CODE
Connect the AC power cord to suitable outlet.
NOTE
This switch should be turned on after you have turned
off all input devices and before
you turn on any devices attached to output.
NOTE
This unit has been manufactured to fit strict quality and
safety standards. PLEASE ENSURE that you use the
correct power supply as shown on the rear panel of
this device. FAILURE to do so many result in shock
and/or serious damage to this unit and/or users.
REAR PANEL
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals